Lithonia Lighting WF4 LED 4 Inch Wafer Recessed Downlight Fixture with Switchable White Color Temperature
Web PricePlease call 1-800-983-1315 for the lowest available price
Lumen:750 (3000K) 810 (4000K) 790 (5000K)lm
|Type of Area||Apartment Buildings, Home & Architectural, Large Retail & Open Areas, Office & Small Retail, Stairwell|
|Certifications||CSA, Energy Star, Title 24 Compliant|
|Lamp Life:||50,000 Hours|
|Dimensions||4.00" x 1.10"|
|Lumen Output:||750 (3000K) 810 (4000K) 790 (5000K)|
|Product Warranty||5 Year|
|Part Number||WF4 LED 30K40K50K 90CRI MB M6 | WF4 LED 30K40K50K 90CRI MW M6 | WF4 LED 30K40K50K 90CRI ORB M6|
|Minimum Start Temperature||-40 Deg F|
|Technology||LED - New Fixture|
|Weight Each||1.00 lb|
Lithonia Lighting's 4-inch round Wafer Switchable white feature allows the user to adjust color temperature with an integrated switch from 3000K, 4000K, or 5000K. Durable housing and high quality light output for shallow ceilings.
The 4" Wafer™ LED Downlight with Switchable White provides high-quality light output and efficiency featuring a switch for easy color temperature adjustment - while eliminating the need for recessed housings. The innovative, slim design allows for easy retrofit, remodel or new construction installation from below the ceiling. The Wafer LED downlight is wet location listed – making it ideal for use in a breadth of outdoor residential, hospitality, commercial and multifamily applications.
Aluminum die cast outer frame. Durable, powder coat paint to prevent rust. FT4 plenum rated cable connector to connect from module to remote driver box. IC rated driver with convenience and value of two remote selectable color temperature options, each with a setting choice to chose either 2700K, 3000K, and 3500K or 3000K, 4000K, and 5000K using the switch. Isolated driver integrated inside steel remote box with four 7/8" knockouts with slots for pryout. Suitable for pulling wires with the 12 cubic-inch wiring compartment to accommodate up to (6) 14 gauge insulated conductors, making the Wafer LED Downlights much easier to wire in 2in/2out (plus ground) daisy-chain applications and contractor friendly.
Ideal for shallow ceiling plenum; no housing required. Steel spring clip for easy installation. 4" cut out template is provided to ensure the correct size hole is cut into ceiling for proper installation of the trim. Size of hole should not exceed 4 1/4 inches for this product. Suitable for installation in t-grid and drop ceiling applications. 3" plenum space required for installation of the remote driver box.
Edge-lit LED technology uses light guided plate to distribute light. Polycarbonate lens provides even illumination throughout the space.
Connect directly to 120V power supply via provided UL recognized driver. High efficient driver with power factor > 0.9. Ambient operating temperature: -40°F (-40°C) to +104°F (+40°C). Dimming down to 10% with most standard incandescent dimers (see list of approved dimmers). Replaces 65W incandescent.
CSA certified to US and Canadian safety standards. ENERGY STAR® certified product. Wet location listed. Air Tight certified in accordance with ASTM E283-2004. Can be used to comply with California Title 24 Part 6 High Efficacy LED light Source Requirements.
5-year limited warranty. Complete warranty terms located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx Note: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C.
How to Install an LED Ultra-Thin Wafer Downlight | Lithonia Lighting: